Updated to follow new header define scheme.

inc/board_config.h

@@ -6,7 +6,7 @@
 //#define FEATHER_RFM96
 
 //Only applied if defined
-    #ifdef FEATHER_RFM9X
+    #ifdef FEATHER_RFM95
         //Define Serial params for debuging
         #define SERIAL_BUADRATE 115200
 
@@ -27,14 +27,14 @@
         #define GPS_BUADRATE 9600            // GPS serial baud rate.
 
         // Radio defines 
-        #define RFM95_CS    8
-        #define RFM95_INT   7
-        #define RFM95_RST   4
-        #define RF95_FREQ 915.0
-        #define RF95_MAX_DB 23
-        #define RF95_MIN_DB 5
-        #define RF95_TIMEOUT 250
-        #define RF95_BUF_SZ 32
+        #define RFM9X_CS    8
+        #define RFM9X_INT   7
+        #define RFM9X_RST   4
+        #define RF9X_FREQ 915.0
+        #define RF9X_MAX_DB 23
+        #define RF9X_MIN_DB 5
+        #define RF9X_TIMEOUT 250
+        #define RF9X_BUF_SZ 32
     #endif //FEATHER_RFM9X
 
 

src/main.cpp

@@ -20,7 +20,7 @@ Adafruit_ST7789 tft = Adafruit_ST7789(TFT_CS, TFT_DC, TFT_RST);  // Initialize d
 CRGB leds[NUM_LEDS];                 // Array to hold LED colors
 SoftwareSerial gpsSerial(GPS_RX_PIN, GPS_TX_PIN);  // Software serial for GPS
 TinyGPSPlus gps;                     // TinyGPS++ object to process GPS data
-RH_RF95 rf95(RFM95_CS, RMF95_INT);  // Radio instance.
+RH_RF95 rf95(RFM9X_CS, RMF9X_INT);  // Radio instance.
 
 
 typedef struct Msg{
@@ -39,36 +39,36 @@ NodeId node = {
     id = 0;
     name = "name";
 };
-uint8_t reciver_buffer[RF95_BUF_SZ];
+uint8_t reciver_buffer[RF9X_BUF_SZ];
 
 void Radio_setup(void) {
-    pinMode(RFM95_RST, OUTPUT);
-    digitalWrite(RFM95_RST, HIGH);
+    pinMode(RFM9X_RST, OUTPUT);
+    digitalWrite(RFM9X_RST, HIGH);
 
     while(!rf95.init()){}
     Serial.println("radio: Initialized");
     
-    if(rf95.setFrequency(RF95_FREQ)) {
+    if(rf95.setFrequency(RF9X_FREQ)) {
         Serial.println("radio: Error could not set frequency");
         while(true){} //Loop forever
     }
     Serial.print("radio: Frequency = ");
-    Serial.println(RF95_FREQ);
+    Serial.println(RF9X_FREQ);
 
-    rf95.setTxPower(RF95_MIN_DB, false);
+    rf95.setTxPower(RF9X_MIN_DB, false);
 }
 
 
 void Radio_reset(void) {
-  digitalWrite(RFM95_RST, LOW);
+  digitalWrite(RFM9X_RST, LOW);
   delay(10);
-  digitalWrite(RFM95_RST, HIGH);
+  digitalWrite(RFM9X_RST, HIGH);
   delay(10);
 }
 
 
 int Radio_SendData() {
-    int8_t tx_power = RF95_MIN_DB;   
+    int8_t tx_power = RF9X_MIN_DB;   
     uint8_t received_id = 0;
 
     //Set the radio output to lowest power.
@@ -78,21 +78,24 @@ int Radio_SendData() {
     rf95.setModeTx();
 
     //Try transmitting data
+    Serial.println("Radio: Sending data...");
     rf95.send(node.id, 1);
     rf95.waitPacketSent();
 
     //Wait for ACK or Radio Msg. (Timeout Should be included).
     //On timeout increase the transmit power and re-attempt.
-    if(!rf95.waitAvailbleTimeout(RF95_TIMEOUT)) {
-        if(rf95.recv(reciver_buffer, RF95_BUF_SZ)) {
+    if(!rf95.waitAvailbleTimeout(RF9X_TIMEOUT)) {
+        if(rf95.recv(reciver_buffer, RF9X_BUF_SZ)) {
         
         }
         else {
             //Failed to receive the message.
+            Serial.println("Radio: Error failed to receive msg.");
         }
     }
     else {
         //No reply of any kind.
+        Serial.println("Radio: Error no reply.");
     }
 
     //Set the radio mode to idle.